LED Turn signals flashing too fast, which resistors?

Hier kun je al je vragen kwijt over elektronica.
badsted
Banden plakker
Berichten: 12
Lid geworden op: di 13 nov 2012, 08:27
Vervoersmiddel: Aprilia SX 50 2011

LED Turn signals flashing too fast, which resistors?

Ongelezen bericht door badsted »

Hello derbi forum,

First of all, i am sorry that i dont speak nl :)

But my problem is that i bought this tail light:

http://www.gearparts24.de/ruecklicht-str8:a4253.html" onclick="window.open(this.href);return false;

And the turn signals are flashing too fast, so i want to put on some resistors, but which resistors should i put on? And how powerful?

My bike is the Aprilia SX 50 year 2011.
Gebruikersavatar
Venlonaer
Pro tuner
Berichten: 1889
Lid geworden op: vr 29 jun 2012, 20:59
Vervoersmiddel: Rieju KTMRX
Honda CR125 '93

Re: LED Turn signals flashing too fast, which resistors?

Ongelezen bericht door Venlonaer »

I'm not sure how much ohm this is, but you'll need this;
http://www.josdijkman.nl/shop/index.php ... uctId=8508" onclick="window.open(this.href);return false;
sendaDRD2012 schreef:Heeft iemand een tip hoe ik verroeste schroeven kan loskrijgen?
the skullkid schreef:Je kan ook gewoon wenen en je tranen er op laten vallen.
derbiAmor
Schakelrijder
Berichten: 155
Lid geworden op: za 12 jan 2013, 14:47
Vervoersmiddel: Derbi Senda DRD 03

Re: LED Turn signals flashing too fast, which resistors?

Ongelezen bericht door derbiAmor »

Hi,

First of all you are going to need load resistors not normal ones. This is because you need to simulate the load that was being created by the indicator bulbs, these resistors are rated at 50% if used constantly ( flashing an indicator I would consider constant for this case as the 0.5 seconds it is off is not enough for it to cool sufficiently. So if you had say a 21w indicator bulb you should not take the 25w load resistor as 50% of 25w is less than your bulb. You should take the next step up which is a 50w. Then to determine the ohm value needed you should google ohm's law and make some calculations.

I would guesstimate around 6-7 ohms.

Or.....

Just do it properly and get a led relais.

Load resistors are chunky and like getting warm.
GEZOCHT: Derbi Senda DRD SM 2003 Supermotard Zadel
Heavy Fuel
Tuner
Berichten: 463
Lid geworden op: za 23 feb 2013, 10:36
Vervoersmiddel: Derbi

Re: LED Turn signals flashing too fast, which resistors?

Ongelezen bericht door Heavy Fuel »

Ze leren tegenwoordig nogen wel wat op school :thumbup:
derbiAmor
Schakelrijder
Berichten: 155
Lid geworden op: za 12 jan 2013, 14:47
Vervoersmiddel: Derbi Senda DRD 03

Re: LED Turn signals flashing too fast, which resistors?

Ongelezen bericht door derbiAmor »

Dat is bijna 10 jaar geleden... Ma goed.
GEZOCHT: Derbi Senda DRD SM 2003 Supermotard Zadel
badsted
Banden plakker
Berichten: 12
Lid geworden op: di 13 nov 2012, 08:27
Vervoersmiddel: Aprilia SX 50 2011

Re: LED Turn signals flashing too fast, which resistors?

Ongelezen bericht door badsted »

Derbiamor, is it possible to change to the LED relais on the Aprilia SX 50, because i cant find my relais. Where is it, can you maybe post a picture?
derbiAmor
Schakelrijder
Berichten: 155
Lid geworden op: za 12 jan 2013, 14:47
Vervoersmiddel: Derbi Senda DRD 03

Re: LED Turn signals flashing too fast, which resistors?

Ongelezen bericht door derbiAmor »

http://wakawakaoo.com/aprilia-rx-50-rac ... g-diagram/

There is a schematic i found. It appears that 14 is the relay, what they call flasher on the diagram, follow the cables, and you will find it. :box:

You can't change the LED relay because you don't have one, you must replace the existing relay you have for a LED one. Should be a real simple rewire...

I don't know where it is as i don't have the same bike as you, though.... visit...

http://images.google.com

search for "aprilia sx 50 flasher relay"

Good luck.
GEZOCHT: Derbi Senda DRD SM 2003 Supermotard Zadel
Plaats reactie